Firestone Splice Adhesive - 1 Gallon

$124.99
Manufacturer: Firestone
SKU: W563587058
Ship to
*
*
Shipping Method
Name
Estimated Delivery
Price
No shipping options

Firestone Splice Adhesive is designed for splicing PondGard EPDM Pond Liners and Firestone 45 mil EPDM Pond Liners and adhering to various substrates as indicated in the Firestone Specialty Products specifications and details.

This product requires Haz-Mat Shipping and cannot be shipped UPS Next-Day Air, Second-Day Air or Three-Day Select

Firestone Splice Adhesive Method of Application

Position the EPDM pond liner to overlap 3" to 6" along the entire length of the splice. Fold the top sheet back and clean the dry mating surfaces per Firestone Specialty Products specifications and details.

Stir the Firestone Pond Liner Splice Adhesive thoroughly before and during use, achieving a uniform mix with no sediment on the bottom and no marbling evident. Apply the Firestone Splice Adhesive with a 3" or 4" thick solvent-resistant paint brush to both mating surfaces at about the same time so as to allow approximately the same flash off time. Apply in a thick, even, smooth coat with long painting type strokes so that the brush marks bleed out, yielding a smooth, glossy adhesive surface. (Make one short backstroke at each field and factory cross seam to leave extra adhesive at the step off.)

Do not use circular motions, paint rollers, spray equipment or mechanical equipment for the application of EPDM liner glue.

Allow the solvents in the Splice Adhesive to flash off completely according to the touch-push test (usually less than 30 minutes, flash off time will vary depending on ambient air conditions).

Once the pond liner glue has dried, allow the top sheet to fall freely on the bottom sheet so as not to stretch or wrinkle the EPDM pond liner. Roll the entire lap splice using a 2" silicone or silicone-sleeved steel hand roller with positive pressure towards the outside edge of the lap, and along the entire length of the lap. Apply seam edge treatment in accordance with Firestone Specialty Products specifications and details.

Firestone Splice Adhesive Coverage Rate

  • 150 linear feet per gallon (including both substrates) with 3" width of finished splice and 4" approximate width of actual adhesive application on one substrate.

 

  • 120 linear feet per gallon including both substrates) with 4" width of finished splice and 5" approximate width of actual adhesive application on one substrate.

Firestone Splice Adhesive is designed for splicing PondGard EPDM Pond Liners and Firestone 45 mil EPDM Pond Liners and adhering to various substrates as indicated in the Firestone Specialty Products specifications and details.

This product requires Haz-Mat Shipping and cannot be shipped UPS Next-Day Air, Second-Day Air or Three-Day Select

Firestone Splice Adhesive Method of Application

Position the EPDM pond liner to overlap 3" to 6" along the entire length of the splice. Fold the top sheet back and clean the dry mating surfaces per Firestone Specialty Products specifications and details.

Stir the Firestone Pond Liner Splice Adhesive thoroughly before and during use, achieving a uniform mix with no sediment on the bottom and no marbling evident. Apply the Firestone Splice Adhesive with a 3" or 4" thick solvent-resistant paint brush to both mating surfaces at about the same time so as to allow approximately the same flash off time. Apply in a thick, even, smooth coat with long painting type strokes so that the brush marks bleed out, yielding a smooth, glossy adhesive surface. (Make one short backstroke at each field and factory cross seam to leave extra adhesive at the step off.)

Do not use circular motions, paint rollers, spray equipment or mechanical equipment for the application of EPDM liner glue.

Allow the solvents in the Splice Adhesive to flash off completely according to the touch-push test (usually less than 30 minutes, flash off time will vary depending on ambient air conditions).

Once the pond liner glue has dried, allow the top sheet to fall freely on the bottom sheet so as not to stretch or wrinkle the EPDM pond liner. Roll the entire lap splice using a 2" silicone or silicone-sleeved steel hand roller with positive pressure towards the outside edge of the lap, and along the entire length of the lap. Apply seam edge treatment in accordance with Firestone Specialty Products specifications and details.

Firestone Splice Adhesive Coverage Rate

  • 150 linear feet per gallon (including both substrates) with 3" width of finished splice and 4" approximate width of actual adhesive application on one substrate.

 

  • 120 linear feet per gallon including both substrates) with 4" width of finished splice and 5" approximate width of actual adhesive application on one substrate.
Write your own review
  • Only registered users can write reviews
*
*
Bad
Excellent
*
*
*